Rinnai Symmetry RDV3611 Installation Manual download pdf (Page 7)

RDV3611 Operation Guide: 11158-B 02-13 | 7

General information

Before operation please read these instructions to get an overview of how to operate,

maintain and service your Rinnai gas ﬁre.

Cladding and ﬁnishes

The Symmetry RDV3611 comes in

two framing options; framed and

frameless. Framed is best suited

to a dry wall/plaster ﬁnish. The

frameless option suits cladding

with a ﬁnished edge, such as, tiles,

brick, or polished granite.

With a framed and frameless

installation the ﬁre is a permanent

ﬁxture. The ﬁre is screwed to the

framing before the cladding. Once

the cladding has been ﬁxed in

place the Symmetry RDV3611 has

been framed into a permanent

position.

The depth of the Symmetry

RDV3611 is adjustable to

accommodate a range of cladding

options. This is important for a

frameless installation to achieve

a ﬂush ﬁnish. Where the edge is

visible, an aluminium edge can be

used to hide the visible cladding.

Electrical connection

The standard

electrical

connection is to

the right hand side

of the heater front

assembly. If necessary this can be

changed by your electrician to

terminate on the left.

The connection is either direct

wired or connected to a power

point within the cavity. A 1500 mm

power cord is supplied with a 3-pin

plug. This must be connected to

a dedicated earthed power point.

The electric isolation switch must

be accessible after the appliance

has been installed.

The heater must not be located

immediately below a socket outlet

(potential ﬁre hazard).

If the supply cord is damaged, it

must be replaced by a licensed

tradesperson. This must be a

genuine replacement part available

from Rinnai, part number 6765B.

Heat transfer kit

The heat transfer ducting

kit is available as an optional

accessory. This allows heat from

the Symmetry RDV3611 to be

transferred to another area of the

house.

It is best to install the kit at the

same time as the ﬁre due to the

additional space required for

installation. The heat transfer kit

must be installed by a licensed

tradesperson.

Installation by a licensed

tradesperson

Ensure your installer talks to you

about the use and care of this

appliance, and that you understand

these instructions. The installer

also needs to complete the

appliance commissioning sheet

and installer details, and leave this

guide with you.

Safety devices

Your Rinnai Symmetry RDV3611 is

designed with the following safety

devices:

- light to pilot

- overheat safety switch

- ﬂame failure

- combustion chamber pressure

relief

Soot deposits

Small soot deposits on the log set

or glass is normal. Signiﬁcant build

up however is not normal and will

require a service call. Refer to the

troubleshooting section for further

information.

TV installation above the

ﬁreplace

If installing a ﬂat

screen TV above the

ﬁre the main issue is

heat. Heat from the

ﬁre and heat from the

ﬂueing components that sit behind

the TV, especially if recessed.

The Symmetry RDV3611 has a fan

that distributes warm air from the

top of the appliance out into the

room. As warm air is dispersed

outwards as opposed to directly

upwards, installation of a TV may

be an option.

For further information please

contact Rinnai or refer to the

installation manual. This illustrates

recommended minimum

clearances when installing a TV

directly above the Symmetry

RDV3611 or into a recess.

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comments to this Manuals

No comments