THIS IS AN UNVENTED GAS-FIRED HEATER. IT USES AIR (OXYGEN)FROM THE ROOM IN WHICH IT IS INSTALLED. PROVISIONS FORADEQUATE COMBUSTION
5. Any compound used on the threaded joint of gas piping shall be a type which resists the action ofliquefied petroleum gas.6. Supplied gas pressu
A. This appliance does not have a pilot. It is equippedwith an ignition device which automatically lights theburner. Do not try to light the burne
- 10 -CONTROL PANEL OPERATING INFORMATIONINSTALLATIONCheck room size and ventilation. Do notoversize. Improper sizing may cause nuisancelock outs.CONT
1. To remove the HEPA filter· Remove the screw using Philips head.· Remove the Filter Screen and the HEPA Filter.2. To install the HEPA filter·
TURNING ONPress the ON/OFF button to operate the heater. The ONindicator will glow green. After approximately 20 secondsthe spark generator will
Press the Economy button to startthe Economy function.The Economyindicator will glow.Press the Economy button once moreto switch off the function.g
OFF TIMER OPERATIONThis feature is useful on cold nights when the unit continues to operate after you have gone tobed.The OFF Timer can be selecte
WARNING· Ensure there are no obstacles or foreign materials directly in front of the appliance where thewarm air will discharge into the room.· En
Air purifier with Plasmacluster Ion Operation 1 Press Air Purifier with Ion button.· When "H" is selected, the unit willcontinually
MAINTENANCE SUGGESTIONSThis heater has been designed and constructed for a long performance life when installed andoperated properly under normal cond
WARNINGTHIS APPLIANCE IS INTENDED FOR SUPPLEMENTAL HEATING. IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVlCE OR MAINTENANCE CAN CAUSE P
5. Install the HEPA Filter in the HEPA Filter Screen· Install the HEPA Filter as illustrated beside.An arrow indicates position of filter installa
Clean air filter at least once a week. Do not wait for filter warninglamp to come on before cleaning filter. Do not use the heater withthe filter wa
Please note: General cleaning, maintenance and wear and tear are not necessarily covered under theguarantee. CaIIs of this nature may be chargeable.-
- 21 -CAUTlON: Label all wires prior to disconnecting when servicing controls. Wire errors cancause improper and dangerous operation. Verify proper
- 22 -
- 23 -
- 25 -
- 26 -
- 27 -No.001 FRONT PANEL RC-592-20-1 1 002 LOUVER ASS’Y RC-592-25-1 1 003 REAR PANEL RC-592-21-2 1 004 TC CHECK HOLDER RC-334-73-1 1 005
- 1 -SPECIFICATIONS Overheat SwitchWhen the heater gets too hot during operation (for example when the filters or air outlet louvers are blocked) t
In all cases, you may be able to clear the Error Message simply by turning the heater OFF, then ON again. If the Error Message still remains or return
- 29 -
Rinnai America Corporation warrants the products described in this warranty including any parts and components thereof, to be free
UNPACK HEATER:Check for damage. (DO NOT INSTALL DAMAGED HEATER.) If heater is damaged, contact yoursupplier for advice. Before installing a heater, ch
- 3 -SAFETY POINTSDo not install this heater in areas wherespray painting or plating is taking place, orin places such as hair dressers, wherethere ma
- 4 -SAFETY POINTSDo not unplug during operationDo not allow children to put articles in thelouvers.Supervise children playing near this heater.Do not
1. Read these rules and the instructions carefully. Check all local codes. Failure to follow these couldcause a malfunction of the heater resultin
NOTICE BEFORE INSTALLATIONThe heater must be installed by a qualified service person according to these installation instructions.When used without ad
Unusually tight construction is defined as construction where:a) Walls and ceilings exposed to the outside atmosphere have a continuous water vapor
Comments to this Manuals