Installation and User ManualRHFE-556TRHFE-556TEnergysaverÑSpace HeaterOperation and Use - Page 2Installation - Page 12Important.Read these instruction
– 8 –ROOM TEMPERATURE ADJUSTMENTSLO 16 18 20 22 24 26 HION/OFFRoom adjustmentRoom temp. indicatorONFILTER-POWER ON / COMBUSTION INDICATORIndicates tha
– 9 – FAN FILTERTo protect the room air fan from dust particles or lint, afilter is situated at the rear of the appliance. Whenthis filter becomes b
– 10 –CARING FOR YOUR NEW RHFE-556TThis appliance is safely controlled. If there is something wrong then it will stop, as it is protected bythe follo
– 11 –PRE-SERVICE CHECKBefore asking for a service call please check the following points.These points are part of the normal operation of the unit.
– 12 –ERROR MESAGESThe Energysaver 556T has the ability to check its own operation continuously. If a fault occurs, anError Message will flash on the
– 13 –INSTALLATION INSTRUCTIONSImportant Safety Instructions1. Gas Safety (Installation & Use) Regulations 1998 are the ‘Rules in Force’.In your o
– 14 –INSTALLATION INSTRUCTIONSSPECIFICATIONInput: 6.4kW (21840 Btu/h) Burner: Stainless Bunsen TypeIgnition: Continuous Spark Gas Inlet: 1/2 inch BSP
– 15 –LOCATIONWhen positioning the heater the main pointsgoverning the location are:1. Flueing2. Warm air distributionThis heater must not be installe
– 16 –LOCATIONDo not flue into natural draught flues or fireplaces,this unit can only be used with one of the six typesof Rinnai flue kits.Do not flue
– 17 –POSITIONING THE FLUE TERMINALOHNNMQMHKBPQQIFLJGCAID,EDimensionABCDEFGHIJKLMNOPQTerminal PositionDirectly below an opening, air brick, opening wi
CONTENTSWarranty ...1Layout of appliance...2Features...4Safety Points...5Operat
– 18 –LOCATIONDo not install the heater in an unusually dusty area.Use a flue guard if the terminal is easily accessibleto children.Check local regula
– 19 –SLEEVE AND MANIFOLD INSTALLATIONMETHOD FOR STANDARD WALLS1. Dis-assemble Manifold from Sleeve.The flue consists of 3 parts, sleeve, insideconnec
– 20 –SLEEVE AND MANIFOLD INSTALLATIONMETHOD FOR STANDARD WALLS5. Check rubber seal is in place on terminal.6. Installation of TerminalFrom outside, i
– 21 –FITTING UNITAIR INLET HOSELOCKING CLAMP, SCREW CLAMP ANDINSULATION.The following components can be fitted by reachingdown the rear of the applia
– 22 –CONNECTING GAS AND ELECTRICAL SERVICES1. GAS CONNECTION.Purge any air or swarf from the gas line. Connect up the appliance to the gas supply us
– 23 –RINNAI 1004T/556T WIRING DIAGRAM USING RANDALL 851 PROGRAMMERNLNLRANDALL 851 TIMERRINNAI 556T10:1 transformer Rinnai UK Part number 957-000-001R
– 24 –GAS CONVERSIONCAUTIONRISK OF ELECTRIC SHOCK❈ Disconnect electrical supply1. Remove bottom trim (pull)2. Remove 8 screws inside bottom louvre,pul
– 25 –TESTINGPRESSURE CHECKING PROCEDURE:Caution- 230 V inside appliance.1. Check that SW6 (Dip switches) are correct for the gastype for which the ap
– 26 –FITTING TOP SPACER + WALL CLIP SECURE HEATER TO WALLFix angle bracket to back spacer with screwsprovided.Fix wall bracket to wall, so that the
– 27 –BLOCK AND WIRING DIAGRAMWIRING DIAGRAMBLOCK DIAGRAMSW6. DIP SWITCHTB1SUB-P.C.BSW1 FM. ADJUST SWITCH〔Hi〕 SW2 FM. ADJUST SWITCH〔Lo〕 SW3 POV. P
– 1 –RINNAI WARRANTY OF QUALITYAs the purchaser of this high quality model RHFE-556T product you are provided with the followingwarranty:Free PartsHea
– 28 –FORCED FLUE HEATER EXTENSION KITS• This extension set is to be used for installations requiring extra distance.MAXIMUM FLUE LENGTH 7 METRES. Re
– 29 – TYPES COMPATIBLE WITH EXTENSION KITRHFE - 556FTR / 556TINSTALLING AN EXTENSION KITInstalling an extension kit requires construction of an air
– 30 –1. How to connect exhaust pipesTo connect the exhaust pipes, fit the male end into the female end and clamp with pipe stopper A toprevent slippi
– 31 – CAUTIONS1. Maximum extendable lengthFOR BEST ROOM AIR HUMIDITY, KEEPWATER IN THE HUMIDIFIER TRAY.2. To prevent water condensationCondensed wat
– 32 –4. Wherever the air intake hose and exhaust piperun sideways, try to have the exhaust pipe ontop (to prevent the air intake hose from saggingont
– 33 –DIMENSIONSSERVICE CONTACT POINT30050214R279R206217 245632750WALL OPENING RANGEAIR SUPPLY CONNECTION5542802807785165GAS CONNECTION13436Contact: R
Jan 2006 556F-2190
– 2 –GETTING TO KNOW YOUR NEW RHFE-556TINDICATOR PANELROOMTEMPERATURESENSORGAS CONNECTIONELECTRICAL CORDHUMIDIFIER TRAYBuilt into the warm airdischarg
– 3 –CONTROL PANEL LAYOUTLO 16 18 20 22 24 26 HION/OFFRoom adjustmentRoom temp. indicatorONFILTER-POWER ON / COMBUSTION INDICATORIndicates that the ap
– 4 –FORCED FLUE SYSTEM PUSH BUTTON IGNITIONAir for combustion is taken from outside theroom and the flue products are exhaustedoutside, keeping the r
– 5 –SAFETY POINTSDo not restrict the warm air discharge byplacing articles in front of the heater.This appliance must not be used for anypurpose othe
– 6 –SAFETY POINTSKeep flammable materials, trees, shrubs, etc,away from the flue terminal.Do not allow anyone to post articles throughthe louvres.LPG
– 7 –OPERATING YOUR NEW RHFE-556T TO OPEN THE CONTROL PANELOpen Control Panel Cover with key provided. TURNING ON (For manual operationplease refer
Comments to this Manuals